Lewmar · Windlass

Lewmar Pro-Series 700 / 1000

The Pro-Series is Lewmar’s compact horizontal windlass for powerboats and small yachts of about 6–11.5 m: a polished 316 stainless housing on deck with motor and gearbox inside, a rope/chain gypsy, a clutch nut for letting go under gravity and a 1/2 in socket for manual recovery. The 700 has a 500 W motor, 320 kg pull and takes chain up to 7 mm; the 1000 has 700 W, 454 kg and chain up to 8 mm, both on 12 V (the 2005 manual also shows a 24 V 1000). The Pro-Fish 700 / 1000 is the same windlass with an automatic free-fall drive cap in place of the clutch nut, the Pro-Fish Pb takes lead-core line, and an upgrade kit converts early Pro-Series units (fitting sheet B2324 under documents); the smaller Pro-Sport 550 shares only a few parts, marked on their rows. Internals changed twice (Gen 1 in the 2005 manual, Gen 2 in the 2007 and 2010 manuals, Gen 3 in the manuals from 2013), so gear, seal, bearing and motor kits depend on the generation: check the serial number before ordering.

Manuals & documents

The links go to Lewmar’s own documents — some as archived copies of pages the maker has since taken down. We host no manuals or drawings.

Wear parts & part numbers

PartOEM numberAlso fitsNote
Chain gypsy660007691,2,3,4—Current dual gypsy for 6 and 7 mm DIN 766, 1/4 in ISO G4 and 1/4 in BBB chain spliced to 12 mm (1/2 in) 3-strand or 8-plait rope. Gen 3 manuals (2013/2015); lewmar.com sells it as 2020201015 (gypsy assembly 68001100) and names it as the alternative to the old single-size 6 mm gypsy 66000112. Fits the Pro-Series 700, the 6/7 mm Pro-Series 1000 and the Pro-Fish 700.
Chain gypsy660001011,5,6,7—Gypsy No. 504 for 8 mm DIN 766, 8 mm ISO 4565 and 5/16 in BBB chain with 14–16 mm (9/16–5/8 in) 3-strand or 16 mm (5/8 in) 8-plait rope; Pro-Series 1000 and Pro-Fish 1000, 8 mm versions. The kit holds gypsy assembly 66500041 and a fitting leaflet; lewmar.com points the older listing 2022373921 to 66000101. Gen 1 equivalent in the 2005 manual: 570-RC0850.
Chain gypsy660001021,5,8—Gypsy No. 516 for 5/16 in ISO G4, 8 mm DIN 766 and 8 mm ISO 4565 chain with 14–16 mm rope; Pro-Series 1000 and Pro-Fish 1000 G4 versions (6657011108, 6656411108).
Chain gypsy660007681,9,10—Gypsy for 14–16 mm lead-core line; Pro-Fish Pb (1000) only. lewmar.com sells it as kit 2022373516 (gypsy 68001096 plus leaflet); the bare gypsy 2022375205 is marked no longer available.
Chain gypsy660001105,11—Single-size gypsy No. 503 for 7 mm DIN 766 and 1/4 in G4/BBB chain with 12 mm rope, fitted to Gen 2 Pro-Series and Pro-Fish 700 (2007 and 2010 manuals). The Pro-Sport uses the same gypsy (shared part). Gen 1 equivalent in the 2005 manual: 5298RC0762. Current units use the dual gypsy 66000769.
Chain gypsy660001125,11,12—Single-size 6 mm DIN 766 gypsy No. 502 of Gen 2 Pro-Series and Pro-Fish 700; the Pro-Sport uses the same gypsy (shared part). lewmar.com offers the dual gypsy 66000769 as the alternative.
Clutch cone660000985,11,1—Clutch nut and cone kit: clutch nut, gypsy cone and the two 5 × 10 mm drive pins. Pro-Series 700 and 1000 in all manuals from 2007 to 2015 (Gen 2 and Gen 3), and the Pro-Sport 550 (shared part). The Pro-Fish uses the drive cap 66000620 instead.
Clutch lever660000991,11,13,14—Clutch lever / installation wrench for the Pro-Series, Pro-Fish and Pro-Sport 550 (shared part). lewmar.com now sells it as 2020200904 and names 66000099 as the alternative to 2022373768; the V700 manual lists the same number.
Top cap660006205,1,15—Pro-Fish drive cap assembly (the automatic free-fall clutch): drive cap, plunger with housing, retaining pin and cap, plunger and retaining springs, grub screw, shoulder screw and spacer. Pro-Fish only; the Pro-Series has the clutch nut instead.
Standard pawl660006175,1,16—Pro-Fish stopper kit: the stopper cam(s) and the screws that hold the stripper and the cam. Pro-Fish only.
Chain stripper660000965,1,17,18—Chain stripper arm with its screws, Pro-Series and Pro-Fish 700 / 1000. lewmar.com sells it as 2020200901 and points the discontinued Pro-Series/Fish stripper 2022373762 to it. The Gen 1 stripper in the 2005 manual is 66200269.
Motor660007631,19,20,21—12 V motor kit for Gen 3 Pro-Series and Pro-Fish 700 and 1000; serials starting 566, 567, 569 or 572 according to dealers (dealer listings only, no Lewmar document: one source). One dealer says gasket and housing are sold separately, another gives Lewmar catalogue number 2020201010. Wattage is unclear: the manuals list this one motor kit for both the 700 (500 W) and the 1000 (700 W); confirm with Lewmar before ordering for a 700.
Motor660001075,11,22—12 V motor kit of the 2007 and 2010 manuals (Gen 2), listed there for both the 700 and the 1000: motor with pinion, screws, dowel, spirol pin and grommets. lewmar.com sells it as 2020200911 titled ‘Pro Series motor 12V 700W’ (product image 66000107). Wattage is unclear: the manuals list it for the 700 (500 W) as well; confirm with Lewmar before ordering for a 700. The 2005 manual (Gen 1) lists the bare motors 66200270 (12 V) and 66200291 (24 V) instead.
Gear set660007601,23,24—Compound gear kit for Gen 3; serials starting 566, 567, 569 or 572 according to dealers (dealer listings only, no Lewmar document: one source); one dealer gives Lewmar catalogue number 2020201007.
Gear set660007611,25—Gears and shaft kit for Gen 3: gear and shaft parts (items 2, 3, 6, 23, 28, 33, 34, 45, 46 and 51 of the 2013/2015 exploded view).
Gear set660006365,11,26—Second compound gear assembly for Gen 2; serials starting 561, 563, 565 or 571 (2007 and 2010 manuals).
Gear set660006355,11,27—Gears and shaft kit for Gen 2: motor pinion, 1st and 2nd compound gears, mainshaft gear, gypsy drive shaft, needle bearings, Teflon washers, circlip, dowel and spirol pin; serials starting 561, 563, 565 or 571.
Gear set6600010628,29—Compound gear kit for Gen 1 (listed on lewmar.com only); the 1st compound gear alone is 66000614.
Seal set660007641,30—Seals and screw kit for Gen 3 (‘P/S Gen 3’ on lewmar.com): seals including the main-case seal (item 24), drive pins and screws per the kit table of the 2013/2015 manuals.
Seal set660007591,31—Gasket kit for Gen 3: the main-case seal (item 24) and six item-25 parts from the 2013/2015 exploded view.
Seal set660001045,11,32,33—Seals and screw kit for Gen 2: both wiper seals, dowels, drive pins, circlip and screws; serials starting 561, 563, 565 or 571 (2007 and 2010 manuals). One dealer lists Lewmar catalogue number 2020200909.
Seal set6600080034,35—Main-case wiper seal 30 × 40 × 7 mm, the seal around the gypsy drive shaft where it leaves the case. lewmar.com sells it as the Pro-Series/Fish wiper seal; it contains seal 610-099, the main-case wiper seal number in the 2005 Gen 1 manual.
Roller bearing660006341,36,37—Bearing kit listed in the Gen 3 manuals (2013/2015): roller clutch, external circlip and needle roller bearings. lewmar.com titles it ‘bearings kit – Gen2’ and dealers differ on whether it is for Gen 2 only or Gen 2 and 3. Serial-number check: the 2007 and 2010 manuals list 66000103 instead (Gen 2 serials 561, 563, 565, 571); read the serial plate before choosing between the two.
Roller bearing660001035,11,38—Bearings kit as listed in the 2007 and 2010 manuals: needle roller bearings, roller clutch and external circlip. lewmar.com now titles it ‘bearings kit – Gen1’. Serial-number check: the 2013/2015 manuals list 66000634 instead; read the serial plate before choosing between the two (Gen 2 serials start 561, 563, 565 or 571).
Fastening kit660001085,11,39,40—Metric base mat and mounting studs, washers and nuts (2007 and 2010 manuals). lewmar.com marks it no longer available and names 66000767 ‘PS/Fish basemat/manual kit’ as the alternative.
Fastening kit660001005,11—Imperial version of the base mat and mounting stud kit (2007 and 2010 manuals).
Circuit breaker680003481,35,41—50 A circuit breaker / isolator for the Pro-Series and Pro-Fish 700 (12 V); the 2005 manual also uses it for the 24 V Pro-Series 1000. Mount it near the battery, dry and within reach; reset by hand after a trip.
Circuit breaker680002401,5,41—70 A circuit breaker / isolator for the Pro-Series 1000, Pro-Fish 1000 and Pro-Fish Pb (12 V).
Control box / solenoid680009391,11,42—Sealed 12 V changeover contactor, supplied with the windlass in the 2010–2015 manuals (700 and 1000); wired with a 3 A fuse in the switch circuit.
Control box / solenoid680009651,11—Contactor box, the alternative to the bare contactor in the 2010–2015 wiring diagrams.
Control box / solenoid680009631,11—Pre-wired control box, the alternative to the bare contactor in the 2010–2015 wiring diagrams.
Control box / solenoid1800020043—12 V control box (contactor in a box): Lewmar’s current option, labelled ‘VX1 / VX1L / V4 / HX1 / Pro Series & Pro Fish 700 1000’.
Control box / solenoid005253135,5—12 V contactor of the Gen 1 and Gen 2 wiring diagrams (2005 and 2007 manuals), used on the Pro-Series 1000 only (Gen 1 24 V: 0052508); the 700 was then switched directly by the toggle switch 0052519. Keep it out of the anchor locker.
Up/down switch680005931,11,35—Guarded rocker switch (up/down), the helm switch supplied with the windlass in the 2010–2015 manuals (in the 2005 and 2007 manuals with the Pro-Series 1000 only). Switch wiring 1.5 mm² (16 AWG); several switches go in parallel.
Up/down switch005251935,5—Reversing toggle switch of the early Pro-Series 700 without contactor (Gen 1 and Gen 2, 2005 and 2007 manuals): a two-wire installation.
Foot switch6800059835,5,11—Deck foot switch set, black (white: 68000597), in the 2005 and 2007 manuals. The 2010 manual lists single deck switches instead: UP 68000884 grey, 68000917 white, 68000889 stainless; DOWN 68000883, 68000918, 68000888.
Remote control6800059935,5,11—Wired hand-held up/down control (2005, 2007 and 2010 manuals); the 2010 manual also lists a deluxe wired remote, 68000524.
Remote control680009671,11,5—Wireless 3-button remote (windlass only), 2010–2015 manuals; the 5-button windlass-plus-thruster version is 68000968. Needs a contactor. The 2007 manual lists the earlier 68000844 / 68000845.
Control arm kit660007661,44,45,46—Pro-Guard rope guard and control arm kit: rope guard 65002005, guard spacer 65002017, control arm 65002006, torsion spring 66200276, pivot pin washer 66200282, grub screw 66200335 and an M6 × 20 screw. Standard in the Gen 3 manuals (2013/2015) and a retrofit for older Pro-Series and Pro-Fish (sheet B10413); the spacer is not used on the Pro-Fish. lewmar.com: 2020201013; the bare rope guard 2022372612 is discontinued in favour of this kit.
Control arm kit660000975,11,47,48—Control arm kit from before the Pro-Guard (Gen 1 and Gen 2, 2007 and 2010 manuals): control arm, pivot, torsion spring, grub screw and pivot pin washer. lewmar.com offers it in place of the discontinued single parts 66200276, 66200282 and 66200335.
Gear train cover kit660007621,49—Gear train cover kit for Gen 3 (‘P/S Gen 3’ on lewmar.com): gear train cover (item 18) with main seal and fixings.
Gear train cover kit660006375,11—Gear train cover kit for Gen 2: cover, six screws, wiper seal and two needle bearings; serials starting 561, 563, 565 or 571 (2007 and 2010 manuals).
Washer kit660007581,50—Washer kit for Gen 3 (‘P/S Gen 3’ on lewmar.com): washers, items 21, 22, 23 and 27 of the 2013/2015 exploded view.
Free-fall conversion kit660006165,1,51,52—Pro-Fish conversion kit (Pro-Series to automatic free-fall): drive cap assembly, stopper cam and longer screws, with Loctite. The 2007 manual and fitting sheet B2324 limit it to Pro-Series serials starting 561 and 571 with a threaded hole in the main-shaft end (Gen 2); the 2013/2015 manuals (Gen 3) still list it. lewmar.com sells it as 2020200929 with B2324 attached.
Plunger kit6600061853—Pro-Fish free-fall plunger kit (all generations; lewmar.com lists the kit without contents).
Retaining pin kit6600061954—Pro-Fish plunger retaining pin kit (lewmar.com lists the kit without contents).
Cap and screw kit6800142455—Pro-Fish drive cap fixing, cap and screw kit (lewmar.com lists the kit without contents).

Numbers checked against the sources below on 13 October 2026. Always confirm against your serial number and exact type before ordering.

Service intervals

TaskInterval
Full serviceAfter each use: rinse with fresh water, keep the rode at least 300 mm (12 in) below the windlass, check the anchor-locker drain and check the rode and its splice for wear1
Electrical connectionsWhen new, check the electrical connections and mounting studs often (first after two or three recoveries); then at least once a year: connections sound and free of corrosion, studs tight, cables undamaged1
ClutchOnce a year, or more often with heavy use: inspect the gypsy (a high-wear part) and the main case around the seal and cover. On refitting, grease the drive pins and put a light smear on the cone and gypsy faces; on the Pro-Fish clean and lubricate the plunger1
GreaseAt least once a year: strip the above-deck drive-shaft parts, clean and re-grease them and check the shaft wiper seal; the gear train is greased for life35
Motor brushesOnce a year: check motor and gearbox for corrosion and blow the brush dust out of the motor11

From Lewmar’s Gen 3 owner’s manual B10490 issue 2 (after-use, electrical and clutch checks), the 2005 Gen 1 manual 66300070 (annual strip-down and grease) and the combined Pro-Sport/Series/Fish manual 65001242 issue 3 of 2010 (motor and brushes). Lewmar gives no operating hours for these windlasses, only ‘after each use’ and ‘yearly’.

Specifications

TypeHorizontal windlass, 316 stainless housing with motor and gearbox all above deck, rope/chain gypsy only (no drum). Pro-Series releases with a clutch nut, Pro-Fish with an automatic free-fall drive cap. Lewmar quotes boats of 6–11.5 m (20–38 ft); the 2007 manual said up to 10.7 m (35 ft) for the 700 and 13.7 m (45 ft) for the 100056,5
VersionsGen 1: 2005 manual (single part numbers, 12 V and 24 V). Gen 2: serial numbers starting 561, 563, 565 or 571 (2007 and 2010 manuals). Gen 3: manuals of 2013 and 2015, kits titled ‘P/S Gen 3’, Pro-Guard rope guard; dealers give serials starting 566, 567, 569 or 572 (dealer listings only, no Lewmar document: one source). Pro-Fish 700, 1000 and 1000 Pb on the same body35,5,11,1,20,24
Years builtOn sale by 2005 (first owner’s manual 66300070 rev A, 2005); Gen 2 manual 2006/07, Gen 3 manual 2013; still in Lewmar’s range in 202635,56
Voltage12 V DC; the 2005 manual (Gen 1) also lists a 24 V Pro-Series 10001,35
Motor700: 500 W; 1000 and Pro-Fish Pb: 700 W1
Max pull / working load700: 320 kg (700 lb) maximum, working load 79 kg (175 lb); 1000: 454 kg (1000 lb) maximum, working load 114 kg (250 lb)1
Chain speedUp to 32 m/min (105 ft/min); normally about 27 m/min (88 ft/min) at 12 V. The 2005 manual gives 35 / 30 m/min for the 24 V Pro-Series 10005,35
Current draw700: 35 A; 1000: 50 A (normal use)1
Breaker / fuse700: 50 A (68000348); 1000 and Pro-Fish Pb: 70 A (68000240)1
Power cable sizeTotal run battery–windlass–battery: 700: 10, 16 or 25 mm² (8, 6 or 4 AWG); 1000: 16, 25 or 35 mm² (6, 4 or 2 AWG), stepping up with the run length to 24 m; voltage drop under 10 %. Switch wiring 1.5 mm² (16 AWG)1
Chain sizeDual gypsy: 6 mm DIN 766, 7 mm DIN 766, 1/4 in ISO G4, 1/4 in BBB. No. 504: 8 mm DIN 766, 8 mm ISO 4565, 5/16 in BBB. No. 516: 8 mm DIN 766, 8 mm ISO 4565, 5/16 in ISO G4. Pb: 14–16 mm lead-core line. Maximum chain 7 mm (1/4 in) on the 700, 8 mm (5/16 in) on the 10001
Rope size12 mm (1/2 in) 3-strand or 8-plait with 6/7 mm chain; 14–16 mm (9/16–5/8 in) 3-strand or 16 mm (5/8 in) 8-plait with 8 mm chain; windlass-grade medium-lay nylon1
ControlGuarded rocker switch 68000593 and changeover contactor 68000939 with a 3 A control fuse supplied; optional contactor box 68000965 or pre-wired control box 68000963, foot switches, hand-held and wireless remotes1
Dimensions146 × 245 × 178 mm (5 3/4 × 9 5/8 × 7 in); one dealer reads these as height × length × width1
MountingMinimum deck thickness 25 mm (1 in); the M8 studs suit deck plus packing of 25–60 mm (1–2 1/4 in). Three 10 mm (3/8 in) stud holes, two 10 mm cable holes and one 76 mm (3 in) hole for the rode; at least 300 mm (12 in) of free fall below, rode leading in from the roller within 6°. The Gen 1/2 manuals use 5/16 in studs for up to 76 mm (3 in)1,5,35
Weight700: 8.5 kg (19 lb); 1000: 9.5 kg (21 lb)1
LubricationGear train factory-greased for life with SFG 100 (white synthetic grease with PTFE); use a similar grease on the external drive-shaft parts35
ModelsKits: 6656011967-310 Pro-Series 700 6/7 mm–1/4 in; 6657011967-311 Pro-Series 1000 6/7 mm–1/4 in; 6657011198-311 Pro-Series 1000 8 mm; 6656211967-310 Pro-Fish 700; 6656411198-311 Pro-Fish 1000 8 mm; 6656411199-311 Pro-Fish 1000 lead line. Units: 6657011108 Pro-Series 1000 G4, 6656411108 Pro-Fish 1000 G4. The kits add breaker, contactor/solenoid and rocker switch56
Warranty5 years, 1 year on motors and electrics (2007 manual); Lewmar’s current product page says 5 years5,56
Manual recoveryStandard 1/2 in (12 mm) drive ratchet in the socket on the driveshaft end opposite the gypsy, turned clockwise, with the clutch tight1

Good to know

  • Read the serial plate before ordering internal parts: Gen 2 units start 561, 563, 565 or 571 (Lewmar’s 2007 and 2010 manuals), and dealers give 566, 567, 569 or 572 for Gen 3 (dealer listings only, one source). Gear, seal, cover and motor kits differ between the generations, while gypsies, the clutch nut kit, lever, stripper kit and breakers are the same in the 2007 and 2015 kit lists.5,1
  • If the rode creeps out on its own, the Pro-Series clutch nut has worked loose (tighten it with the lever) or the Pro-Fish internal clutch has not re-engaged (press UP briefly). Either way, make the rode fast to a cleat or chain stopper: the windlass is not a mooring point.1
  • Sluggish or dead: measure at the motor while hauling. Lewmar wants about 13.5 V on a 12 V system; well below 11 V points to undersized cable, corroded joints or a weak battery, and constant low voltage kills the motor. Only replace the contactor or motor after the voltage checks out.5
  • Water is what kills these motors: keep the anchor-locker drain clear, check that the motor is dry and rust-free if the locker has flooded, and rinse the windlass with fresh water but never jet-wash it.11
  • On a Pro-Fish gypsy change the shoulder screw is Loctited (warm it to loosen). On reassembly use Loctite 638, 262 or 2701, torque to 21 Nm (15.4 lbf·ft) and wait 15 minutes, but keep threadlocker out of the free-fall threads or the free-fall stops working.51
  • Keep a 1/2 in drive ratchet aboard: it fits the socket on the shaft end opposite the gypsy for manual recovery when the power fails.1

Videos & how-tos

Links to YouTube, nothing embedded. The maker’s own channel comes first; the rest are channels we found clear and correct for this model.

On the marketplace

Looking for a part for the Lewmar Pro-Series 700 / 1000 and Pro-Fish windlasses? Post a wanted ad in the app — it is free, it sits on the live map, and boaters nearby who have the part aboard can answer.

Got spares you no longer need? List them in a minute. No commission, ever.

Get the app

Sources

  1. web.archive.org/web/20190803210317/https://www.lewmar.com/sites/default/files/sites/defau…
  2. lewmar.com/dual-gypsy-for-pro-series-2020201015
  3. lewmar.com/pro-s-6-7mm-dual-gypsy-assy-2022375209
  4. citimarinestore.com/en/lewmar-windlasses/18994-lewmar-pro-series-gypsy-rc-14-14g4-67mm-66…
  5. web.archive.org/web/20071213092341/http://www.lewmar.com/support/PDF/B10490%20Iss2%20Pro%…
  6. lewmar.com/pro-ser-gypsy-rc8mm-5-16-bbb-66000101
  7. lewmar.com/pro-series-5-16-gypsy-assy-2022373921
  8. lewmar.com/pro-ser-gypsy-rc-5-16-g4-516-66000102
  9. lewmar.com/pro-fish-pb-gypsy-kit-2022373516
  10. lewmar.com/pb-gypsy-for-pro-windlasses-2022375205
  11. web.archive.org/web/20160528115358/http://www.lewmar.com:80/sites/default/files/Lewmar-Su…
  12. lewmar.com/pro-series-gypsy-rc6mm-502-66000112
  13. lewmar.com/pro-series-clutch-lever-2020200904
  14. lewmar.com/clutch-lever-pro-series-2022373768
  15. lewmar.com/pro-fish-drive-cap-66000620
  16. lewmar.com/pro-fish-stopper-kit-66000617
  17. lewmar.com/pro-series-stripper-kit-2020200901
  18. lewmar.com/pro-series-fish-stripper-2022373762
  19. lewmar.com/p-s-gen-3-12v-motor-kit-66000763
  20. marine-deals.co.nz/lewmar-pro-series-fish-gen-3-motor-kit-12v/p/149935
  21. citimarinestore.com/es/molinete-lewmar/19016-lewmar-p-s-gen-3-kit-de-motor-12v.html
  22. lewmar.com/pro-series-motor-12v-700w-2020200911
  23. lewmar.com/compound-gear-kit-ps-gen-3-66000760
  24. citimarinestore.com/es/molinete-lewmar/19037-lewmar-pro-series-kit-de-engranaje-compuesto…
  25. lewmar.com/gears-shaft-kit-ps-gen-3-66000761
  26. lewmar.com/compound-gear-kit-ps-gen-2-66000636
  27. lewmar.com/gears-shaft-kit-ps-gen-2-66000635
  28. lewmar.com/compound-gear-kit-ps-gen-1-66000106
  29. lewmar.com/1st-compound-gear-gen1-pro-ser-66000614
  30. lewmar.com/p-s-gen-3-seals-screw-kit-66000764
  31. lewmar.com/p-s-gen-3-gasket-kit-66000759
  32. lewmar.com/pro-series-seals-screws-kit-66000104
  33. citimarinestore.com/en/lewmar-windlasses/19015-lewmar-ps-seals-dowels-and-screws-kit-6600…
  34. lewmar.com/pro-series-fish-wiper-seal-66000800
  35. web.archive.org/web/20051025143543/http://www.lewmar.com:80/support/PDF/Pro%20Series%20Ow…
  36. lewmar.com/pro-series-bearings-kit-gen2-66000634
  37. citimarinestore.com/es/molinete-lewmar/19026-lewmar-pro-series-kit-de-rodamientos-2g.html
  38. lewmar.com/pro-series-bearings-kit-gen1-66000103
  39. lewmar.com/pro-series-fastening-kit-mm-66000108
  40. lewmar.com/ps-fish-basemat-manual-kit-66000767
  41. lewmar.com/circuit-breaker
  42. lewmar.com/changeover-contactor-12v-seale-68000939
  43. lewmar.com/windlass-control-box-contactor
  44. lewmar.com/mst_attachment/attachment/click/attachment_id/302/
  45. lewmar.com/pro-guard-control-arm-kit-2020201013
  46. lewmar.com/pro-series-fish-rope-guard-2022372612
  47. lewmar.com/pro-series-control-arm-kit-66000097
  48. lewmar.com/pro-series-torsion-spring-66200276
  49. lewmar.com/p-s-gen-3-gear-train-cover-kit-66000762
  50. lewmar.com/p-s-gen-3-washer-kit-66000758
  51. lewmar.com/mst_attachment/attachment/click/attachment_id/150/
  52. lewmar.com/pro-fish-conversion-kit-2020200929
  53. lewmar.com/pro-fish-plunger-kit-66000618
  54. lewmar.com/pro-fish-retaining-pin-kit-66000619
  55. lewmar.com/profish-cap-screw-kit-68001424
  56. lewmar.com/windlass-pro-series

Lewmar is a trademark of its owner; boatparts.app is not affiliated with it. Part numbers are quoted for identification only. Spotted an error? Write to mail@boatparts.app.